QEMU for Docker

QEMU in a docker container using KVM acceleration.

Features

• KVM acceleration
• Graceful shutdown

Usage

Via docker-compose.yml

version: "3"
services:
    qemu:
        container_name: qemu
        image: kroese/docker-qemu:latest
        environment:
            DISK_SIZE: "16G"
            BOOT: "http://www.example.com/image.iso"
        devices:
            - /dev/kvm
        cap_add:
            - NET_ADMIN                       
        ports:
            - 22:22
        restart: on-failure
        stop_grace_period: 1m        

Via docker run

docker run -it --rm -e "BOOT=http://www.example.com/image.iso" --device=/dev/kvm --cap-add NET_ADMIN kroese/docker-qemu:latest

FAQ

• How do I check if my system supports KVM?

  To check if your system supports KVM run these commands:

  sudo apt install cpu-checker
  sudo kvm-ok
  

  If kvm-ok returns an error stating KVM acceleration cannot be used, you may need to change your BIOS settings.

• How do I change the bootdisk?

  You can modify the BOOT setting to specify the URL of any ISO image:

  environment:
    BOOT: "http://www.example.com/image.iso"
  

  It will be downloaded only once, during the first run of the container.

• How do I change the size of the data disk?

  By default it is 16GB, but to increase it you can modify the DISK_SIZE setting in your compose file:

  environment:
    DISK_SIZE: "16G"
  

  To resize the disk to a capacity of 8 terabyte you would use a value of "8T" for example.

• How do I change the location of the data disk?

  By default it resides inside a docker volume, but to store it somewhere else you can add these lines to your compose file:

  volumes:
    - /home/user/data:/storage
  

  Just replace /home/user/data with the path to the folder you want to use for storage.

• How do I change the space reserved by the data disk?

  By default the total space for the disk is reserved in advance. If you want to only reserve the space that is actually used by the disk, add these lines:

  environment:
    ALLOCATE: "N"
  

  This might lower performance a bit, since the image file will need to grow every time new data is added to it.

• How do I change the amount of CPU/RAM?

  By default a single core and 512MB of RAM is allocated to the container.

  To increase this you can add the following environment variabeles:

  environment:
    CPU_CORES: "4"
    RAM_SIZE: "2048M"
  

• How do I give the container its own IP address?

  By default the container uses bridge networking, and uses the same IP as the docker host.

  If you want to give it a seperate IP address, create a macvlan network.

  For example:

  $ docker network create -d macvlan \
      --subnet=192.168.0.0/24 \
      --gateway=192.168.0.1 \
      --ip-range=192.168.0.100/28 \
      -o parent=eth0 vlan
  

  Modify these values to match your local subnet.

  Now change the containers configuration in your compose file:

  networks:
      vlan:             
          ipv4_address: 192.168.0.100
  

  And add the network to the very bottom of your compose file:

  networks:
      vlan:
          external: true
  

  This also has the advantage that you don't need to do any portmapping anymore, because all ports will be fully exposed this way.

  NOTE: You will not be able to reach this IP from the Docker host, as macvlan does not allow communication between those two. There are some ways to fix that if necessary, but they go beyond the scope of this FAQ.

• How can the container get an IP address via DHCP?

  First follow the steps to configure the container for macvlan (see above), and then add the following lines to your compose file:

  environment:
      DHCP: "Y"
  devices:
      - /dev/vhost-net
  device_cgroup_rules:
      - 'c 510:* rwm'
  

  NOTE: The exact cgroup rule may be different than 510 depending on your system, but the correct rule number will be printed to the log output in case of error.